Brookfield DV-II+ Programmable Viscometer Instrukcja Użytkownika Strona 38
- Strona / 75
- Spis treści
- BOOKMARKI
Oceniono. / 5. Na podstawie oceny klientów
Brookfield Engineering Labs., Inc. Page 38 Manual No. M/97-164-F1102
Figure 67 shows the grid where the operator programs are
created. It is used to view and edit the B.E.V.I.S. programs.
When the software starts, an empty grid appears on the left of
the screen. You can choose up to 25 commands for your
program. Highlight each command in the list box to the right of
this grid, then click on the Insert button to insert that same
command into the highlighted line of the grid. This same
insertion task can also be accomplished by double-clicking on
the appropriate command in the list box to the right.
In the case of a speed command (SSN), the Speeds
list box becomes enabled when the cursor is placed in
the parameter column for an SSN command. Click on the
down arrow to display a list of available speeds. Click on the
desired speed, and it will be inserted into the appropriate
parameter column in the program grid. The same applies to the
spindle command (SSP).
Select the COM (RS-232) port the Programmable DV-II+ viscometer is connected to
from the COM Port drop down list.
Click the Open File button to load existing B.E.V.I.S. programs.
Click the Save File button to save the B.E.V.I.S. program displayed in the grid.
Click the Print button to print the B.E.V.I.S. program displayed in the grid.
Click the Insert button to insert the B.E.V.I.S. command selected in the Commands
box into the selected row in the program grid.
The buttons shown on the main screen are explained below.
Figure 67
- BROOKFIELD DV-II+ 1
- PROGRAMMABLE VISCOMETER 1
- Operating Instructions 1
- Manual No. M/97-164-F1102 1
- + is in the OFF position 6
- II. GETTING STARTED 10
- + default screen: 10
- 6.0RPM6.0 % 15.6 12
- 6.0RPM12 % 15.6 12
- 6.0RPM % 15.6 14
- 60 RPM % 100 14
- SR 40.0 20.1C 14
- 10 RPM % 8.2 15
- 10 RPM % 19.7 16
- 10 RPM P% 19.7 16
- PRINTER ERROR 17
- CHECK CONNECTION 17
- III. OPTIONS 19
- TIME TO TORQUE 21
- L°F(FAHRENHEIT) 22
- CGS UNITS 22
- LSEQUENTIAL 24
- PRINT SERIAL 24
- PRINT PARALLEL 24
- 10 RPM A% 19.7 25
- TIMED STOP DONE 27
- SET TORQUE:00% 28
- SELECT RPM: 30 28
- Figure 35 29
- LTIME TO TORQUE 30
- SET PRINT TIME 30
- LPRINT INTERVAL 30
- SET MIN’S: 00 30
- RUN PGM SLOT#1 33
- PRESS ENTER 33
- USE SPINDLE 31 33
- PRESS A KEY 33
- CP 123.4 55.1C 34
- 10 RPM PGM% 63.7 34
- IV. DVLOADER SOFTWARE 35
- Figure 66 37
- Figure 67 38
- • Set PC PROG to “OFF.” 39
- IV. 5 Example Programs 40
- (time to torque measurement) 40
- Figure A1 42
- Figure A2 43
- Figure A3 43
- Figure A4 43
- Figure A5 44
- Figure A6 44
- Appendix B - Viscosity Ranges 46
- (1-100 RPM 47
- Table D1 51
- Table D1 (continued) 52
- Table D2 52
- +/-) 0.1°C 54
- °C, 93.3°C, 149°C 54
- + Viscometer 56
- TK = 1.0 from Table D2 58
- SMC = 10 from Table D1 58
- RV Guardleg 59
- LV Guardleg 59
- Appendix F - Speed Sets 61
- Appendix G - Communications 62
- Analog Output: 64
- Figure H1 65
- Figure H2 67
- Figure H3 67
- ❏ Spindle Does Not Rotate 68
- ❏ Inaccurate Readings 69
- VISCOMETER SETUP 70
- ENTER TO START 70
- READY PRINTER 70
- SETUP COMPLETE 71
- TURN POWER OFF 71
- Warranty 72
- Foam Insert 73
- (please list all): 74
- VISCOSITY TEST REPORT 75
Powiązane produkty i podręczniki dla Urządzenia pomiarowe Brookfield DV-II+ Programmable Viscometer
(64 strony)Electrolux ESL8350RO manuales
Manuales del propietario y guías del usuario para Lavaplatos Electrolux ESL8350RO.
Ofrecemos 4 manuales en pdf Electrolux ESL8350RO para descargar gratis por tipos de documentos: Manual de usuario
Komentarze do niniejszej Instrukcji